Product Description
DAC Industries Standard Exit Bar Gate Kit w/ Detex Advantex Stainless Exit Bar (10035-KIT)
- Standard Exit Bar Gate Kit — Surface-mount panic hardware package for free, code-friendly egress on gate applications.
- Detex Advantex Stainless Exit Bar — Choose 36" (#10003) or 48" (#10004) for high-traffic, high-durability performance.
- 24" Adjustable Mounting Plate — Adapts to gate frames approximately 29"–52" wide for clean alignment.
- Adjustable Receiver Bracket — Sized for 3" O.D. latch posts; fine-tunes for smooth, repeatable latching.
- Stainless Tek Screws & Fasteners — Hardware sized for typical chain link and ornamental frames.
- Exit-Only Function — No exterior entry hardware included (free egress only).
The DAC Industries 10035-KIT builds a tougher exit-only gate using Detex’s stainless Advantex device, a favorite for high-use environments that demand long service life. The 24" adjustable plate spans common gate frame widths so layout is quick, and the receiver bracket is designed for a 3" O.D. latch post to simplify strike alignment. Choose a 36" or 48" bar to match opening size and visibility needs, then fasten with the included stainless hardware for a clean, field-friendly install. If you eventually need keyed re-entry or alarmed egress, there are direct upgrade paths that leverage the same gate geometry.
Specifications
| Kit / SKU | 10035-KIT — Standard Exit Bar Gate Kit (exit-only) |
| Exit Device | Detex Advantex stainless bar #10003 (36") or #10004 (48") |
| Mounting Plate | 24" tall plate; adjusts for ~29"–52" gate frame widths; pre-drilled for exit bar |
| Receiver / Strike | Adjustable receiver bracket for 3" O.D. latch post |
| Included Hardware | Stainless Tek screws and fasteners for typical gate frames |
| Function | Exit-only egress (no exterior lock hardware included) |
| Compatibility | Chain link & ornamental metal gate frames; 3" O.D. latch post |
Why Choose This
- Stainless workhorse — Advantex’s stainless construction is built for weather and wear in high-traffic gates.
- Gate-optimized fit — The plate and receiver are sized for common frame widths and latch posts to speed alignment.
- Clear upgrade paths — Need re-entry or alarm later? Consider the 10045 Premium kit (Advantex + lock box) or the 10037 alarmed kit.
Installation (Quick Steps)
- Fit the plate to the gate leaf (≈29"–52" span); clamp, mark, and fasten square to the hinge line.
- Mount the receiver on the 3" O.D. latch post; adjust for clean bolt throw and sure re-latch.
- Install the exit bar (#10003 or #10004) to the pre-drilled plate; test egress and fine-tune alignment.
- Final checks — Cycle repeatedly, tighten fasteners, and confirm code-required signage where applicable.
Buying Guide
- Outside entry needed? Choose a lock-box kit such as 6045 Superior (V40 + lock box) or step up to 10045 Premium (Advantex + lock box).
- Audible notification? Pick the alarmed 10037 kit.
- Budget & duty cycle — For value with strong performance, a Detex V40 kit may suffice; for harsher sites, stay with Advantex.
Frequently Asked Questions
- Does the 10035-KIT allow entry from the outside of the gate?
- No. The 10035-KIT is exit-only. For keyed re-entry, select a kit with a lock box and cylinder (e.g., 10045 Premium or 6045 Superior).
- What gate widths will the 24-inch mounting plate cover?
- The plate adjusts to typical gate frame widths of approximately 29" to 52".
- Which Advantex bar lengths are available in this kit?
- Choose the stainless Detex #10003 (36") or #10004 (48") to fit your opening and visibility needs.
Comparison
- 10035-KIT (this product) — Exit-only kit with stainless Detex Advantex #10003/#10004; 24" plate; receiver for 3" O.D. post.
- 10037-KIT (Advantex, Alarmed) — Adds an integral alarm for exit notification and deterrence.
- 10045-KIT (Advantex + Lock Box) — Adds lock box & keyed cylinder for controlled outside entry.
