Product Description
OZCO® OWT™ Ironwood Post-to-Beam Bolt Offset Connector — 2-Pack (For 6″+ Posts)
- Offset Bolt Pattern — Top plate uses offset bolt holes to maximize bite and spacing on the beam
- “Third Hand” Ledge — Integrated post ledge base supports the beam while you mark and fasten for faster, safer installs
- Adjusts to Beam Thickness — Interlocking top cover plate self-registers to the ledge and accommodates smooth or rough-cut beams
- Outdoor-Ready Build — 3/16″ galvanized steel with a durable black powder coat; ACQ-compatible
- OWT System Match — Coordinates with Ironwood posts, bases, cap nuts, and fasteners for a cohesive look
- Two Connectors per Pack — Use one pack per post-to-beam connection (left/right)
The OZCO OWT Ironwood Post to Beam Offset Bolt Connector is an elegant solution to connecting your wood beams to 6" or larger posts. The revolutionary 2-piece design has a ledge that lets you rest your beam on the connector while making your measurements; it acts as a second set of hands that holds the beam in place until you are ready to attach it, reducing time and labor on the project. These connectors are offset, which means that the bolt holes on the upper plate are slightly offset from each other. These are used for perpendicular beams where you need the bolts to not run into each other. Inline OWT Post to Beam Connectors are also available for attaching parallel beams.
Post to Beam Connectors are designed for roofs, pergolas, rafters, & other structures. These Ironwood themed connectors are designed for both strength and style with a 3/16" galvanized steel construction and a high-quality powder coat that provides a premium look that will last for years, indoor or out. OWT products can also be used for unlimited alternative projects like furnishings & architectural applications.
The Ironwood Post to Beam Connectors match the rest of the Ironwood Series from OZCO OWT Hardware. This style is characterized by clean lines, crisp angles, and an industrial chic style that is designed to elevate the look of your project.
Each OWT Post to Beam Offset Connector includes:
- 2 - Ironwood Post Ledge Base Plates
- 2 - Ironwood Top Plates with Offset Holes
- 4 - 1-1/2" Hex Cap Nuts
- 4 - 2-3/4" OWT Timber Screws (Used for bottom plate placement only)
The Ironwood Post to Beam Offset Connector DOES NOT include OWT Timber Bolts, which are required for installation. You need to choose the size of Timber Bolt that best meets your needs. 4 bolts are needed, and are sold separately.
Why Choose This
- Faster layout — Ledge supports the beam so one person can position and fasten
- Reliable connection — Offset top holes spread load and reduce fastener conflict
- Built to last — 3/16″ galvanized substrate + powder coat for long service life outdoors
Specifications
| Style / Item # | Ironwood — 51736 (P2B-BO-IW) | |
| Post Size | Designed for 6″ or larger wood posts | |
| Beam Compatibility | Top cover plate interlocks with ledge and adjusts to beam thickness; works with smooth or rough-cut lumber | |
| Material / Finish | 3/16″ galvanized steel with black exterior powder coat; ACQ-approved | |
| Pack Quantity | 2 connectors per pack (one post ledge base + one top plate per side) | |
| Kit Contents | (2) Ironwood post-ledge base plates (2) Ironwood top cover plates (offset pattern) (4) 1-1/2″ OWT Hex Cap Nuts (4) OWT Timber Screws for bottom-hole placement |
|
| Fasteners Required* | (4) OWT Timber Bolts for the top holes (sold separately). Screws are not recommended in the top holes. | |
| Typical Usage | Pergolas, pavilions, porch roofs, heavy decorative framing | |
*Follow engineering, span, and embedment requirements for your project and local code.
Installation
Dry-fit and mark your beam location. Fasten the post-ledge base to the post; set the beam on the ledge. Position the top cover plate, then drill and install the required OWT Timber Bolts through the top holes. Use the included OWT Timber Screws only for the bottom hole placement. Tighten hardware, verify alignment, and repeat for the opposite side.
Buying Guide
- Offset vs. Inline: Choose this Offset model to stagger top bolt holes; use the Inline model when you need the top bolts aligned.
- Don’t forget fasteners: Add OWT Timber Bolts (top holes), plus matching Hex Cap Nuts to finish exposed faces.
- Coordinate the look: Keep extra OWT 1/4″ Timber Screws on hand for adjacent OWT brackets.
Frequently Asked Questions
- Will this work on 4×4 posts?
- It’s designed for 6″ and larger posts; use per manufacturer guidance and your project’s engineering.
- Are Timber Bolts included?
- No. Timber Bolts are required for the top holes and are sold separately.
- Can I use screws in the top holes?
- No. The manufacturer recommends Timber Bolts for the top holes; screws are not recommended there.
- Does it fit rough-cut beams?
- Yes. The interlocking top plate adjusts to beam thickness and works with smooth or rough-cut lumber.
Comparison
- Post-to-Beam Bolt Offset (this item): Staggered top holes; great when you want maximum spacing between bolts.
- Post-to-Beam Bolt Inline: Top holes align; choose when layout or aesthetics call for a straight bolt line.
- OWT-Lite Post-to-Beam: Lighter-duty alternative for select applications while keeping the OWT look.
Need help kitting Timber Bolts, cap hardware, and matching OWT brackets? Contact us—we’ll help you plan counts and compatible components for a clean, code-conscious build.
