Product Description
OZCO® OWT™ Laredo Sunset® 8″ Post-to-Beam Coupler for Seams — 2-Pack (Black, 3/16″ Steel)
- Splice Over a Post — Purpose-built to couple two beams in-line at an intermediate (non-terminal) post for clean, aligned “seam” joints
- “Third-Hand” Ledge — Integrated post ledge supports both beam ends while you align, mark, and fasten
- Through-Bolt Capacity — Top holes are designed for OWT Timber Bolts (required; sold separately) to deliver strong clamping at the seam
- Outdoor-Ready — Heavy 3/16″ pre-galvanized steel with a durable black exterior powder coat; ACQ-compatible
- Laredo Sunset Aesthetic — Signature LS styling coordinates with matching OWT brackets, bases, and accents
The Laredo Sunset Post to Beam Coupler is designed to connect two beams to a post in-line, at the seam. These are used for non-terminal posts. The unique ledge of the coupler enables you to set your beams and hold them in place while you complete your measurements, and then attach them without needing another set of hands.
These Post to Beam Couplers fit any standard 2" beam, from 1.45" actual to 2" actual size. The 2-piece design makes them adjustable, and the top plate slides onto the bottom plate to until it hits the wood, ensuring a snug connection.
The Laredo Sunset style has a southwestern charm that looks hand forged, not mass produced. Instead of spending hours, and extra money, trying to hide your connection hardware, OWT-Hardware is designed to become an integral part of your project's aesthetic, adding to its overall look.
Each OWT Laredo Sunset Post to Beam Coupler includes:
- 2 - Laredo Sunset Post Ledge Bases
- 2 - Laredo Sunset Top Cover Plates
- 4 - Hex Cap Nuts
- 4 - 2-3/4" OWT Timber Screws
The Laredo Sunset Post to Beam Coupler DOES NOT include OWT Timber Bolts, which are required to connect the top plate to the beam. Choose the size of Timber Bolt that best meets your needs. 8 Timber Bolts are required, and can be purchased separately.
Why Choose This
- Cleaner seams — Purpose-made hardware aligns and clamps beam ends right at the post
- Faster installs — The ledge supports members so one person can work more safely
- Built to last — Galvanized substrate + exterior powder coat for long outdoor service
Specifications
| Series / Style | Laredo Sunset® (OWT) — 8″ Post-to-Beam Coupler for Seams | |
| Intended Use | Splice two beams inline over a post (non-terminal “seam” connection) | |
| Material / Finish | 3/16″ pre-galvanized steel with a black exterior-grade powder coat; ACQ-approved | |
| Pack Quantity | 2 connectors per pack (one for each face/side of the post) | |
| Kit Includes (per 2-pack) | (2) Post ledge bases; (2) Top cover plates; (4) 1-1/2″ OWT Hex Cap Nuts; (4) OWT Timber Screws (for lower placement hole) | |
| Fasteners Required (top holes) | OWT Timber Bolts (sold separately). Screws are not recommended in the top holes. | |
| Typical Usage | Pergolas, pavilions, porch roofs, long beam runs, rafters | |
Installation
Dry-fit both beam ends at the post. Fasten the post ledge bases to the post, set beam ends on the ledge, and place the top cover plates. Drill the top holes and install OWT Timber Bolts through the beam(s) and plate; use the included OWT Timber Screws only in the designated lower placement hole. Tighten, verify alignment, and repeat on the opposite face. Follow local code and your project’s engineering for spans and loads.
Resource: Manufacturer’s Warranty
Buying Guide
- Don’t forget bolts: Add OWT Timber Bolts for the top holes; finish exposed faces with OWT Hammered Dome Cap Nuts or OWT Hex Cap Nuts.
- Mix with standard joints: For non-seam post/beam joints on the same project, see Laredo Sunset Post-to-Beam Bolt (Inline) or the Bolt (Offset).
Frequently Asked Questions
- Is this the right part for joining two beams end-to-end at a post?
- Yes. The coupler is specifically intended for inline “seam” connections at intermediate posts.
- Do I have to use Timber Bolts?
- Yes for the top holes. Timber Bolts provide the clamping needed for a secure seam; screws are not recommended in the top holes.
- Will it match my other Laredo Sunset hardware?
- Yes. The geometry and black powder coat coordinate with the Laredo Sunset OWT line.
- Can I use this at the very end of a beam run?
- It’s designed for seam splices at intermediate posts. For end/terminal joints, use a standard Post-to-Beam connector.
Comparison
- Laredo Sunset 8″ Coupler (this item): Designed for seam splices over a post; requires Timber Bolts in top holes.
- Laredo Sunset Post-to-Beam Bolt — Inline/Offset: Standard post/beam joints (not a seam); also through-bolted for higher clamping.
- Laredo Sunset Post-to-Beam (OWT-Lite): Lighter-gauge, screw-fastened connectors for typical residential applications.
Have questions about mixing couplers and standard post-to-beam brackets on the same build? Contact us and we’ll help you plan the right combination of connectors and fasteners for a cohesive, code-conscious project.
